RFC 735 (rfc735) - Page 1 of 1
Revised Telnet byte macro option
Alternative Format: Original Text Document
RFC 735 DHC RHG 3 Nov 77 42083
Telnet Byte Macro Option
Network Working Group David H. Crocker
RFC: #735 Rand-ISD
NIC: #42083 (Dcrocker at Rand-Unix)
Richard H. Gumpertz
Carnegie-Mellon University
(Gumpertz at CMU-10A)
Obsoletes: RFC #729 (NIC #40306) 3 November 1977
Revised TELNET Byte Macro Option
1. Command name and code:
BM 19
2. Command Meanings:
IAC WILL BM
The sender of this command REQUESTS or AGREES to use the BM
option, and will send single data characters which are to be
interpreted as if replacement data strings had been sent.
IAC WON'T BM
The sender of this option REFUSES to send single data characters
which are to be interpreted as if replacement data strings had
been sent. Any existing BM definitions are discarded
(i.e., reset to their original data interpretations).
IAC DO BM
The sender REQUESTS or AGREES to have the other side (sender of
WILL BM) send single data characters which are to be interpreted
as if replacement data strings had been sent.
IAC DON'T BM
The sender REFUSES to allow the other side to send single data
characters which are to be interpreted as if replacement data
strings had been sent. Any existing BM definitions
are to be discarded.
1
RFC 735 DHC RHG 3 Nov 77 42083
Telnet Byte Macro Option
IAC SB BM IAC SE
where:
is the data byte actually to be sent across the
network; it may NOT be Telnet IAC (decimal 255, but may be any
other 8-bit character.
is one 8-bit byte binary number, indicating how many
characters follow, up to the ending IAC
SE, but not including it. Note that doubled IACs in the
definition should only be counted as one character per pair.
is a string of zero or more Telnet ASCII
characters and/or commands, which the is to
represent; any character may occur within a . Note, however, that an IAC in the string must be
doubled, to be interpreted later as an IAC; to be interpreted
later as data byte 255, it must be quadrupled in the original
specification.
The indicated will be sent instead of the indicated
. The receiver of the (the sender
of the DO BM) is to behave EXACTLY as if the
string of bytes had instead been received from the network. This
interpretation is to occur before any other Telnet
interpretations, unless the occurs as part of a
Telnet command; in this case no special interpretation is to be
made. In particular, an entire Telnet subnegotiation (i.e. from
IAC SB through IAC SE) is to be considered a Telnet command in
which NO replacement should be done.
The effect of a particular may be negated by reseting
it to "expand" into itself.
IAC SB BM X IAC SE may be used to cause X to be
ignored in the data stream.
is decimal 1.
IAC SB BM IAC SE
The receiver of the for accepts the
requested definition and will perform the indicated replacement
whenever a is received and is not part of any IAC
Telnet command sequence.
2
RFC 735 DHC RHG 3 Nov 77 42083
Telnet Byte Macro Option
is decimal 2.
IAC SB BM IAC SE
The receiver of the for refuses to perform
the indicated translation from to because the particular is not an acceptable
choice, the length of the exceeds available
storage, the length of the actual did not
match the length predicted in the , or for some unspecified
reason.
is decimal 3.
may be
which is decimal 1;
(for receiver's storage) which is decimal
2;
(of actual string compared with promised
length in ) which is decimal 3; or
(intended for use only until this document
can be updated to include reasons not
anticipated by the authors) which is
decimal zero (0).
IAC SB BM IAC SE
The is to be treated as real data, rather than as
representative of the
Note that this subcommand cannot be used during Telnet
subcommands, since subcommands are defined to end with the next
occurrence of "IAC SE". Including this BM subcommand within any
Telnet subcommand would therefore prematurely terminate the
containing subcommand.
is decimal 4.
IAC SB BM IAC SE
The RECEIVER of the defined (i.e., the sender of IAC
DO BM) requests the sender of to cancel its
definition. is the same as for the subcommand.
3
RFC 735 DHC RHG 3 Nov 77 42083
Telnet Byte Macro Option
The sender should (but is not required to) respond by
resetting (i.e., sending an IAC SB BM IAC SE).
If the receiver absolutely insists on cancelling a given macro,
the best it can do is to turn off the entire option, with IAC DONT
BM, wait for an acknowledging IAC WONT BM and then restart the
option, with IAC DO BM. This will reset all other macroes as well
but it will allow the receiver to REFUSE with code BAD CHOICE
if/when the foreign site attempts to redefine the macro in
question.
3. Default:
WON'T BM -- DON'T BM
No reinterpretation of data bytes is done.
4. Motivation for the option:
Subcommands for Telnet options currently require a minimum of five
characters to be sent over the network (i.e., IAC SB